|
Part Number |
Description |
Price/Unit (RM) |
|
ersb102 |
Magnastick 102 Metal detector |
|
Feature-Packed for Versatility! The
Magnastick 102 magnetic locator provides the
same basic performance features as the
Magnastick 100. However, with the addition
of our push-button "erase" feature, greater
flexibility is achieved and performance is
enhanced. When a magnetic disturbance, such
as a metal fence, is confronted, simply
press the "erase" button and the disturbance
is erased for continued searching without
interference. No need to reduce the
sensitivity; the Magnastick 102 always
returns to perfect magnetic balance when the
"erase" button is pressed. The Magnastick
102 locator also includes a power line
indicator feature. The LCD panel visually
indicates that a power line is present.
(CAUTION: This feature is an aid only and is
not intended for locating buried power
lines.)
Ideal for tests on telephone lines
or electronic equipment, the C.A
6533 megohmmeter measures insulation
at 50V, 100V, 250V and 500V, as well
as resistance. It indicates the
AC/DC voltage before each
measurement.
insulation: up to 20GΩ at 50V, 100V,
250V and 500V
voltage indication before insulation
measurement: 0 to 600V AC/DC
(blocking if U>25V)
resistance: 0 to 400kΩ
giant 4,000-count display + bargraph
(simultaneous reading of the
measurement and analogue variation)
backlit display
programmable alarms
DREL function for testing for the
presence of transmission frame or
measurement of the difference in
resistance between 2 wires of a pair
remote control probe (option)
back stand for use on a table or on
the ground
long battery life: 6 x 1.5V
batteries
Measurements in compliance with IEC
61557, NF C 15-100, VDE 0413
electrical safety: IEC 1010 300V
Cat. III
|
Part Number |
Description |
Price/Unit (RM) |
|
CS880
|
METAL DETECTOR |
|
The C.Scope CS880 is a neat solution to the
problem of pinpointing the position of metal
covers buried under earth or tarmac.
DM-800 features:
•
Autoranging, 3-5/6-digit, 5000-count
display for greater accuracy.
•
Frequency and capacitance
measurements plus diode and
continuity
tests standard.
•
Data hold to capture measurements.
•
RS-232 capable, may be connected to
a PC for extended measurement
capability with optional optically
isolated interface DMSC-8L or
DMSC-9, purchased separately.
•
Low ohm range calibration, subtracts
test lead resistance.
•
Backlit display for easy viewing.
DM-810 also features:
•
True RMS for no-compromise accuracy.
DM-820 also features:
•
Record max, min and max-min
readings.
•
Crest capture (5ms peak hold) max,
min and max-min readings.
•
Relative offset display mode to see
relative changes in measurements.
•
Temperature measurement standard.
Accessories included:
(1)
9V battery, protective boot,
carrying case
(DM-820, DM-810), bead temperature
probe (DM-820 only,
400ºF/204ºC max), test leads.
•
Lifetime Limited Warranty.
SPECIFICATIONS
Voltage Measurement
50.00, 500.0mV; 5.000, 50.00, 500.0, 1000V
Amperage Measurement
500.0, 5000μA; 50.00, 500.0mA; 5.000, 10.00A
Resistance
50.00, 500.0Ω; 5.000, 50.00, 500.0kΩ; 5.000,
50.00MΩ
Capacitance
50.00, 500.0nF; 5.000, 50.00, 500.0, 9999μF
Frequency
10Hz-125kHz
Temperature K type,
-58°F to 1832°F (-50°C to 1000°C)
Measurement Category
CAT IV, 600V; CAT III 1000V
Spec:
-
Voltage Measurement: 60mV to
1000V AC/DC
-
Amperage Measurement: 600mA to
8A AC/DC
-
Resistance: 600Ω to 60MΩ
-
Frequency (Hz): 50 ~ 400
-
Measurement Category: Cat IV,
300V; Cat III 600V, Cat II 1000V
|
Description:
Auto and manual ranging
Non-contact and single-probe voltage
detection
Beep-Jack™ audible and visible warning
to guard against improper A and mA terminal
plug in.
High visibility 6000 count LCD display.
Auto power off, display backlight,
analog bar graph
PC interface capability using optional
USB RS-232 cable with data recording PC
software.
Lifetime Limited Warranty.
|
|
